TS-2000 display mod

I recently acquired a TS-2000 again to be more active on VHF/UHF (Satellite, EME and other weak signal fun). One thing I never liked about the TS-2000 was the display. Especially after seeing the various images on the web with modified displays to have a nice light blue color. Searching for more info, I came across a few folks who are selling “kits” for $24+. We are talking about 6 LEDs and 3 resistors. Since I was not going to pay that much for parts worth $4 max. I moved ahead in the true spirit of amateur radio/ hardware hacking: If you can’t open it, you don’t own it. So let’s go and break stuff Smile.

Note: If you are not comfortable opening your radio, looking inside and find out how things work, please stop reading. I will not be responsible if you damage or destroy anything beyond repair! For the rest: let’s get some solder melted, shall we?

The LEDs are 3mm in diameter and I used cool blue LEDs from this eBay seller. Note they are flat headed instead of round which gives a more even light distribution. The resistors are standard 150 Ohm 1/4W.

ts2000-1

I for the first time in my many years of playing with electronics played it safe and used a anti-static mat. It appears I’m getting old and risk the danger of growing up Smile.

You can pull off all the knobs from the radio and also remove the rubber ring from the VFO knob.

ts2000-2

Next, remove the top and bottom cover. Start with removing all screws and then gently lift off both covers. The front panel is held by 4 screws on the sides. Only remove the top ones and loosen the lower screws. This allows you to tilt the front panel forward. I put the radio next to the edge of the desk and let the panel hang down.

ts2000-3

Next unplug those two cables on the left side of the panel. Be gentle, take your time!

ts2000-4

The flat ribbon cable that connects the front panel control board to the main board can slowly and gently be pulled out. BE CAREFUL!
Now you can remove the remaining two screws and remove the entire front panel assembly. Set the radio aside on a safe spot making sure nothing is underneath it that could damage the main board!

ts2000-6

Use a hex wrench to loosen the VFO knob and pull it off.

ts2000-7

Once the VFO knob is removed, you’ll have access to the rotary encoder for the VFO. Remove the nut and lift off the resistance mechanism. Remove the screw that attaches the front panel cover to the board. Once those two are removed, you can loosen the plastic latches on top and bottom of the panel cover and carefully remove it. Be careful not to break them. Slow and steady wins the race.

ts2000-8

Now you should have the front panel board lying in front of you. This is also a good time to clean the knobs depending on the age of your radio some dust may have accumulated. Loosen the 4 screws marked in the image to remove the display. DO NOT LIFT IT OFF FAST!

ts2000-9

Carefully lifting the display up will reveal the flat ribbon cable that attaches the display. Unlike me, you were smarter and unplugged it before loosening the 4 screws. But this is now the second chance to do so. Again, very carefully pull it out. Make sure not to bend it as you want to get it back in once we’re done.

ts2000-10

Place the display board in front of you and you’ll see the 6 lamps and three resistors. Do not use solder wick to remove them! This is the one time in this job where you can really suck! Use a solder suction pump and remove the solder. Be careful not to overheat the traces. Take multiple steps. The resistors can be tricky so take your time.

ts2000-11

Place the LED into the hole. The anode goes towards the side facing the resistor. Double check before soldering! I cut the legs about 4mm short and bent them over.

ts2000-12

Once done, this (or better) is what it should look like. Make sure you don’t have cold solder joints. If in doubt, quickly re-heat and make sure your solder joints are nice and shiny. Repeat the steps for all 6 LEDs and the 3 resistors making sure everything lines up, no solder bridges and polarity of the LEDs is correct. Then it’s time to assemble everything in reverse as you took it apart. Be careful when pushing the flat band cables back into the sockets. Slow and steady! You have to make sure they are in the right angle. Also make sure you push them all the way in to have proper contact. I did not do it with the one connecting the front panel to the main chassis and subsequently the radio wouldn’t turn on. Also make sure that no wires are touching the fan (which I should’ve replaced at the same time with a less noisy one).

ts2000-13

If you’ve done everything right, this is what your first smoke test should look like. A nice cool blue display greeting you and NO smoke coming out anywhere. Congratulations. Now put the rest back together and enjoy your new much more pleasing IMHO display.

7 thoughts on “TS-2000 display mod

  1. Hi, the link you gave for ebay seller pointed to a cool white led instead odf cool blue one… Are you sure about the color you purchased ?

  2. This is great, What size are the original resistors? could you not have just ordered ones in the new value in the original size to make it a little cleaner of an install?

    thanks a ton

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s